Always been a bloke in the pub or car boot or whatever that can supply hooky dvds or games or hacked satellite, FAST always talks tough about busting them.

Early eights it was disk and tape trading, mostly tape trading in the UK. Was a way more social activity.

Late 80s and early 90s, it was all disk, and you really needed a connected friend who could get the menu disks (custom pirated compilation disks). These were often super hoarded, only traded for a lot of games, like certain private trackers today.

Very early web stuff was all usenet and ftp servers, often hosted at a university. If you knew where to look, anything was accessible.

Early 2000s was a golden period of easy access. It would be slow, and the quality would often be low if it was a video or mp3. It’s gotten harder to find the obscure stuff as time has gone on. I

t’s like the scene only remembers out and out classics or the latest thing outside of some niche places.

I have a few that will be very close as I decided a bit over a decade ago to limit myself to one rewatch a year of each to stop myself sucking all the joy out of them:

• Alien - my favorite survival horror

• Aliens - my favorite Nam movie

• Jaws - my favorite version of Moby Dick, although I really like Godzilla Minus One take on Jaws

• Jurassic Park - best big stompy monster film for me

• Lord of the Rings - this is always over Christmas. Its not faithful enough for me to the books but it still manages to be an outstanding Trilogy.

• Emperors New Groove - favorite body swap film

Never tried sharpening them myself, always used a service as standard jobber bits are less than a pound to get done for you. I normally save up a bunch of stuff including saw blades and get them done at once to save on shipping at hit the low volume discounts.

However, its only worth doing on quality components, I wouldn’t pay a pound or waste my own time to get a cheap ass drill bit sharpened, I would just replace it.

My saw blades start at like £70 so paying £12 to get it sharpened is good value, but a £30 blade is not really worth it, not least for which it won’t cut anywhere near as much material before getting blunt between sharpens. Same logic for drill bills, some of my SDS ones are over £30 each, my augur bits can be over £50 each, so those are worth looking after, not going to bother for a set of 10 bits for £20.

But don’t cheap out on drill bits, nor should you try and use the same drill bit for like a decade without sharpening it.

Think of drill bits like a good, sharp knife. Knives cut far better and far easier when they sharp, exactly the same with drill bits. If you trying to cut something you would normally pick the right type of knife to do the job, exactly the same with drill bits.

If you driving screws or other fasteners with your drill consider better quality driver bits if you have a lot of them to drive, such as building a deck. Good quality driver bits cam out far far less and will take more torque so be faster/go in better. Using cheap driver bits is probably worse than using cheap drill bits.

I use powershell for work as I need the m365 modules for work and its very flexible with decent module availability to plug in all sorts.

However it absolutely sucks for large data handling, anything over 10k rows is just horrendous, I typically work with a few million rows. You can make it work with using .Net to process it within your script but its something to be aware of. Being able to extend with .Net can be extremely useful.

So I used to be massively into warhammer 30k and 40k, I have over 100k of points of models probably over 200k. I used to have one of the largest book collections going, over £12k worth when I sold it. Yet I dropped out the hobby after several decades because

*My main army is space marines and they started killing them off so that they could reissue the entire range but worse *They dumbed down the rules progressively more and more *30k rollout and tournament support just stopped meaning that my huge investment didn’t get used anywhere near enough *models became more monopose

• New book releases of the same quality just stopped, because they wouldn’t pay to keep the big name authors

Plenty of people like the new direction, I don’t as it stole the ground from under me and required I rebuy in for worse.

Gravy or curry sauce

The latter every time. It’s made much worse as it’s almost always achieved via a leveraged buy out, saddling the business with huge debt and absolving the vulture from most of the risk. It’s used as a one way ticket to stripping the company of any value.

So this is obviously McDonald’s but manufacturing suffers a similar path:

1. Make high quality and respected product onshore
2. Get purchased by vulture capitalist
3. Lower standards to increase profit
4. Product is offshored to cover up falling sales
5. Quality nosedives
6. Once the customer base catches on sales nosedives
7. Lower quality even more and brand becomes a joke
8. Get purchased by mega conglomerate who collects brands like Pokémon
9. Rival product gets made onshore by a small team who used to work for you

See Doc Martin and Solvair or Hunter Wellingtons or any other of a large number of former halo brands. Filson is one going through this right now